/****************************************************************************** * * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved. * * This program is free software; you can redistribute it and/or modify it * under the terms of version 2 of the GNU General Public License as * published by the Free Software Foundation. * * This program is distributed in the hope that it will be useful, but WITHOUT * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for * more details. * * You should have received a copy of the GNU General Public License along with * this program; if not, write to the Free Software Foundation, Inc., * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA * * ******************************************************************************/ //***** temporarily flag ******* #define CONFIG_SINGLE_IMG //#define CONFIG_DISABLE_ODM //for FPGA VERIFICATION config #define RTL8188E_FPGA_TRUE_PHY_VERIFICATION 0 //***** temporarily flag ******* /* * Public General Config */ #define AUTOCONF_INCLUDED //#define RTL871X_MODULE_NAME "92EU" #define DRV_NAME "rtl8192eu" #define CONFIG_USB_HCI #define PLATFORM_LINUX //#define CONFIG_IOCTL_CFG80211 #ifdef CONFIG_IOCTL_CFG80211 //#define RTW_USE_CFG80211_STA_EVENT /* Indecate new sta asoc through cfg80211_new_sta */ #define CONFIG_CFG80211_FORCE_COMPATIBLE_2_6_37_UNDER //#define CONFIG_DEBUG_CFG80211 //#define CONFIG_DRV_ISSUE_PROV_REQ // IOT FOR S2 #define CONFIG_SET_SCAN_DENY_TIMER #endif /* * Internal General Config */ //#define CONFIG_PWRCTRL //#define CONFIG_H2CLBK #define CONFIG_EMBEDDED_FWIMG //#define CONFIG_FILE_FWIMG #define CONFIG_XMIT_ACK #ifdef CONFIG_XMIT_ACK #define CONFIG_ACTIVE_KEEP_ALIVE_CHECK #endif #define CONFIG_80211N_HT #define CONFIG_RECV_REORDERING_CTRL //#define CONFIG_TCP_CSUM_OFFLOAD_RX //#define CONFIG_DRVEXT_MODULE //#define CONFIG_SUPPORT_USB_INT #ifdef CONFIG_SUPPORT_USB_INT //#define CONFIG_USB_INTERRUPT_IN_PIPE #endif #define CONFIG_HIGH_CHAN_SUPER_CALIBRATION //#define CONFIG_DISABLE_MCS13TO15 1 // Disable MSC13-15 rates for more stable TX throughput with some 5G APs #define CONFIG_IPS #ifdef CONFIG_IPS //#define CONFIG_IPS_LEVEL_2 //enable this to set default IPS mode to IPS_LEVEL_2 #endif #define SUPPORT_HW_RFOFF_DETECTED #define CONFIG_LPS #if defined(CONFIG_LPS) && defined(CONFIG_SUPPORT_USB_INT) //#define CONFIG_LPS_LCLK #endif #ifdef CONFIG_LPS_LCLK #if defined(CONFIG_HIGH_CHAN_SUPER_CALIBRATION) #undef CONFIG_HIGH_CHAN_SUPER_CALIBRATION #endif #endif #ifdef CONFIG_LPS_LCLK #define CONFIG_XMIT_THREAD_MODE #endif //befor link //#define CONFIG_ANTENNA_DIVERSITY //after link #ifdef CONFIG_ANTENNA_DIVERSITY #define CONFIG_HW_ANTENNA_DIVERSITY #endif //#define CONFIG_CONCURRENT_MODE #ifdef CONFIG_CONCURRENT_MODE //#define CONFIG_HWPORT_SWAP //Port0->Sec , Port1 -> Pri #define CONFIG_RUNTIME_PORT_SWITCH //#define DBG_RUNTIME_PORT_SWITCH #define CONFIG_STA_MODE_SCAN_UNDER_AP_MODE //#define CONFIG_ATMEL_RC_PATCH //#define CONFIG_TSF_RESET_OFFLOAD // For 2 PORT TSF SYNC. #endif //#define CONFIG_IOL #define CONFIG_AP_MODE #ifdef CONFIG_AP_MODE //#define CONFIG_INTERRUPT_BASED_TXBCN // Tx Beacon when driver BCN_OK ,BCN_ERR interrupt occurs #if defined(CONFIG_CONCURRENT_MODE) && defined(CONFIG_INTERRUPT_BASED_TXBCN) #undef CONFIG_INTERRUPT_BASED_TXBCN #endif #ifdef CONFIG_INTERRUPT_BASED_TXBCN //#define CONFIG_INTERRUPT_BASED_TXBCN_EARLY_INT #define CONFIG_INTERRUPT_BASED_TXBCN_BCN_OK_ERR #endif #define CONFIG_NATIVEAP_MLME #ifndef CONFIG_NATIVEAP_MLME #define CONFIG_HOSTAPD_MLME #endif #define CONFIG_FIND_BEST_CHANNEL //#define CONFIG_NO_WIRELESS_HANDLERS //#define CONFIG_AUTO_AP_MODE #endif #define CONFIG_P2P #ifdef CONFIG_P2P //The CONFIG_WFD is for supporting the Wi-Fi display #define CONFIG_WFD #ifndef CONFIG_WIFI_TEST #define CONFIG_P2P_REMOVE_GROUP_INFO #endif //#define CONFIG_DBG_P2P #define CONFIG_P2P_PS //#define CONFIG_P2P_IPS #define CONFIG_P2P_OP_CHK_SOCIAL_CH #define CONFIG_CFG80211_ONECHANNEL_UNDER_CONCURRENT //replace CONFIG_P2P_CHK_INVITE_CH_LIST flag #define CONFIG_P2P_INVITE_IOT #endif // Added by Kurt 20110511 //#define CONFIG_TDLS #ifdef CONFIG_TDLS // #ifndef CONFIG_WFD // #define CONFIG_WFD // #endif // #define CONFIG_TDLS_AUTOSETUP // #define CONFIG_TDLS_AUTOCHECKALIVE #endif //#define CONFIG_EFUSE_CONFIG_FILE #define CONFIG_SKB_COPY //for amsdu #define CONFIG_LED #ifdef CONFIG_LED //#define CONFIG_SW_LED #ifdef CONFIG_SW_LED //#define CONFIG_LED_HANDLED_BY_CMD_THREAD #endif #endif // CONFIG_LED #ifdef CONFIG_IOL #define CONFIG_IOL_NEW_GENERATION #define CONFIG_IOL_READ_EFUSE_MAP //#define DBG_IOL_READ_EFUSE_MAP #define CONFIG_IOL_LLT #define CONFIG_IOL_EFUSE_PATCH #define CONFIG_IOL_IOREG_CFG //#define CONFIG_IOL_IOREG_CFG_DBG #endif #define USB_INTERFERENCE_ISSUE // this should be checked in all usb interface #define CONFIG_GLOBAL_UI_PID #define CONFIG_LAYER2_ROAMING #define CONFIG_LAYER2_ROAMING_RESUME //#define CONFIG_ADAPTOR_INFO_CACHING_FILE // now just applied on 8192cu only, should make it general... //#define CONFIG_RESUME_IN_WORKQUEUE //#define CONFIG_SET_SCAN_DENY_TIMER #define CONFIG_LONG_DELAY_ISSUE #define CONFIG_NEW_SIGNAL_STAT_PROCESS //#define CONFIG_SIGNAL_DISPLAY_DBM //display RX signal with dbm #define RTW_NOTCH_FILTER 0 /* 0:Disable, 1:Enable, */ #define CONFIG_DEAUTH_BEFORE_CONNECT #define CONFIG_BR_EXT 1 // Enable NAT2.5 support for STA mode interface with a L2 Bridge #ifdef CONFIG_BR_EXT #define CONFIG_BR_EXT_BRNAME "br0" #endif // CONFIG_BR_EXT #define CONFIG_TX_MCAST2UNI 1 // Support IP multicast->unicast //#define CONFIG_CHECK_AC_LIFETIME 1 // Check packet lifetime of 4 ACs. /* * Interface Related Config */ #ifndef CONFIG_MINIMAL_MEMORY_USAGE #define CONFIG_USB_TX_AGGREGATION #define CONFIG_USB_RX_AGGREGATION #endif #define CONFIG_PREALLOC_RECV_SKB //#define CONFIG_REDUCE_USB_TX_INT // Trade-off: Improve performance, but may cause TX URBs blocked by USB Host/Bus driver on few platforms. //#define CONFIG_EASY_REPLACEMENT /* * CONFIG_USE_USB_BUFFER_ALLOC_XX uses Linux USB Buffer alloc API and is for Linux platform only now! */ //#define CONFIG_USE_USB_BUFFER_ALLOC_TX // Trade-off: For TX path, improve stability on some platforms, but may cause performance degrade on other platforms. //#define CONFIG_USE_USB_BUFFER_ALLOC_RX // For RX path #ifdef CONFIG_USE_USB_BUFFER_ALLOC_RX #undef CONFIG_PREALLOC_RECV_SKB #endif /* * USB VENDOR REQ BUFFER ALLOCATION METHOD * if not set we'll use function local variable (stack memory) */ //#define CONFIG_USB_VENDOR_REQ_BUFFER_DYNAMIC_ALLOCATE #define CONFIG_USB_VENDOR_REQ_BUFFER_PREALLOC #define CONFIG_USB_VENDOR_REQ_MUTEX #define CONFIG_VENDOR_REQ_RETRY //#define CONFIG_USB_SUPPORT_ASYNC_VDN_REQ #define WAKEUP_GPIO_IDX 14 //WIFI Chip Side /* * HAL Related Config */ #define RTL8192E_RX_PACKET_INCLUDE_CRC 0 #define SUPPORTED_BLOCK_IO #define RTL8188E_FW_DOWNLOAD_ENABLE //#define CONFIG_ONLY_ONE_OUT_EP_TO_LOW 0 #define CONFIG_OUT_EP_WIFI_MODE 0 #define ENABLE_USB_DROP_INCORRECT_OUT //#define RTL8192CU_ADHOC_WORKAROUND_SETTING #define DISABLE_BB_RF 0 //#define RTL8191C_FPGA_NETWORKTYPE_ADHOC 0 #ifdef CONFIG_MP_INCLUDED #define MP_DRIVER 1 #define CONFIG_MP_IWPRIV_SUPPORT 1 //#undef CONFIG_USB_TX_AGGREGATION //#undef CONFIG_USB_RX_AGGREGATION #else #define MP_DRIVER 0 #endif /* * Platform Related Config */ #ifdef CONFIG_PLATFORM_MN10300 #define CONFIG_SPECIAL_SETTING_FOR_FUNAI_TV #define CONFIG_USE_USB_BUFFER_ALLOC_RX #if defined (CONFIG_SW_ANTENNA_DIVERSITY) #undef CONFIG_SW_ANTENNA_DIVERSITY #define CONFIG_HW_ANTENNA_DIVERSITY #endif #if defined (CONFIG_POWER_SAVING) #undef CONFIG_POWER_SAVING #endif #endif//CONFIG_PLATFORM_MN10300 #ifdef CONFIG_PLATFORM_TI_DM365 #define CONFIG_USE_USB_BUFFER_ALLOC_RX #endif /* * Outsource Related Config */ #define RTL8192CE_SUPPORT 0 #define RTL8192CU_SUPPORT 0 #define RTL8192C_SUPPORT (RTL8192CE_SUPPORT|RTL8192CU_SUPPORT) #define RTL8192DE_SUPPORT 0 #define RTL8192DU_SUPPORT 0 #define RTL8192D_SUPPORT (RTL8192DE_SUPPORT|RTL8192DU_SUPPORT) #define RTL8723AU_SUPPORT 0 #define RTL8723AS_SUPPORT 0 #define RTL8723AE_SUPPORT 0 #define RTL8723A_SUPPORT (RTL8723AU_SUPPORT|RTL8723AS_SUPPORT|RTL8723AE_SUPPORT) #define RTL8723_FPGA_VERIFICATION 0 #define RTL8188EE_SUPPORT 0 #define RTL8188EU_SUPPORT 0 #define RTL8188ES_SUPPORT 0 #define RTL8188E_SUPPORT (RTL8188EE_SUPPORT|RTL8188EU_SUPPORT|RTL8188ES_SUPPORT) #define TESTCHIP_SUPPORT 0 #define RTL8812E_SUPPORT 0 #define RTL8812AU_SUPPORT 0 #define RTL8812A_SUPPORT (RTL8812E_SUPPORT|RTL8812AU_SUPPORT) #define RTL8821A_SUPPORT 0 #define RTL8723B_SUPPORT 0 #define RTL8192E_SUPPORT 1 #define RTL8813A_SUPPORT 0 //#if (RTL8188E_SUPPORT==1) #define RATE_ADAPTIVE_SUPPORT 0 #define POWER_TRAINING_ACTIVE 0 //#endif #ifdef CONFIG_USB_TX_AGGREGATION //#define CONFIG_TX_EARLY_MODE #endif #ifdef CONFIG_TX_EARLY_MODE #define RTL8192E_EARLY_MODE_PKT_NUM_10 0 #endif #define CONFIG_80211D /* * Debug Related Config */ #define DBG 1 //#define CONFIG_DEBUG /* DBG_871X, etc... */ //#define CONFIG_DEBUG_RTL871X /* RT_TRACE, RT_PRINT_DATA, _func_enter_, _func_exit_ */ #define CONFIG_PROC_DEBUG #define DBG_CONFIG_ERROR_DETECT //#define DBG_CONFIG_ERROR_DETECT_INT //#define DBG_CONFIG_ERROR_RESET //#define DBG_IO //#define DBG_DELAY_OS //#define DBG_MEM_ALLOC //#define DBG_IOCTL //#define DBG_TX //#define DBG_XMIT_BUF //#define DBG_XMIT_BUF_EXT //#define DBG_TX_DROP_FRAME //#define DBG_RX_DROP_FRAME //#define DBG_RX_SEQ //#define DBG_RX_SIGNAL_DISPLAY_PROCESSING //#define DBG_RX_SIGNAL_DISPLAY_SSID_MONITORED "jeff-ap" #define DBG_RX_SIGNAL_DISPLAY_RAW_DATA //#define DBG_TX_POWER_IDX //#define DBG_SHOW_MCUFWDL_BEFORE_51_ENABLE //#define DBG_ROAMING_TEST //#define DBG_HAL_INIT_PROFILING //#define DBG_MEMORY_LEAK 1 //TX use 1 urb //#define CONFIG_SINGLE_XMIT_BUF //RX use 1 urb //#define CONFIG_SINGLE_RECV_BUF